实例介绍
function Line_Asign
port_handles = get_param(gcbh,'PortHandles');%获取选中的Subsystem port句柄
inport_handles = port_handles.Inport;%获取输入port的句柄
for i = 1:length(inport_handles)
line_handles = get_param(inport_handles(i),'Line');%Subsystem的连线的句柄
src_handles = get_param(line_handles,'SrcBlockHandle');
port_pos = get(inport_handles(i),'Position');
src_pos = get_param(src_handles,'Position');
src_len = src_pos(3) - src_pos(1);
src_width = src_pos(4) - src_pos(2);
new_pos(1) = port_pos(1) - 100;
new_pos(3) = new_pos(1) src_len;
new_pos(2) = port_pos(2) - fix(src_width/2);
new_pos(4) = port_pos(2) fix(src_width/2);
set_param(src_handles,'Position',new_pos);
end
outport_handles = port_handles.Outport;%获取输出port的句柄
for j = 1:length(outport_handles)
line_handles = get_param(outport_handles(j),'Line');%Subsystem的连线的句柄
src_handles = get_param(line_handles,'DstBlockHandle');
port_pos = get(outport_handles(j),'Position');
src_pos = get_param(src_handles,'Position');
src_len = src_pos(3) - src_pos(1);
src_width = src_pos(4) - src_pos(2);
new_pos(1) = port_pos(1) 100;
new_pos(3) = new_pos(1) src_len;
new_pos(2) = port_pos(2) - fix(src_width/2);
new_pos(4) = port_pos(2) fix(src_width/2);
set_param(src_handles,'Position',new_pos);
end
end
port_handles = get_param(gcbh,'PortHandles');%获取选中的Subsystem port句柄
inport_handles = port_handles.Inport;%获取输入port的句柄
for i = 1:length(inport_handles)
line_handles = get_param(inport_handles(i),'Line');%Subsystem的连线的句柄
src_handles = get_param(line_handles,'SrcBlockHandle');
port_pos = get(inport_handles(i),'Position');
src_pos = get_param(src_handles,'Position');
src_len = src_pos(3) - src_pos(1);
src_width = src_pos(4) - src_pos(2);
new_pos(1) = port_pos(1) - 100;
new_pos(3) = new_pos(1) src_len;
new_pos(2) = port_pos(2) - fix(src_width/2);
new_pos(4) = port_pos(2) fix(src_width/2);
set_param(src_handles,'Position',new_pos);
end
outport_handles = port_handles.Outport;%获取输出port的句柄
for j = 1:length(outport_handles)
line_handles = get_param(outport_handles(j),'Line');%Subsystem的连线的句柄
src_handles = get_param(line_handles,'DstBlockHandle');
port_pos = get(outport_handles(j),'Position');
src_pos = get_param(src_handles,'Position');
src_len = src_pos(3) - src_pos(1);
src_width = src_pos(4) - src_pos(2);
new_pos(1) = port_pos(1) 100;
new_pos(3) = new_pos(1) src_len;
new_pos(2) = port_pos(2) - fix(src_width/2);
new_pos(4) = port_pos(2) fix(src_width/2);
set_param(src_handles,'Position',new_pos);
end
end
好例子网口号:伸出你的我的手 — 分享!
小贴士
感谢您为本站写下的评论,您的评论对其它用户来说具有重要的参考价值,所以请认真填写。
- 类似“顶”、“沙发”之类没有营养的文字,对勤劳贡献的楼主来说是令人沮丧的反馈信息。
- 相信您也不想看到一排文字/表情墙,所以请不要反馈意义不大的重复字符,也请尽量不要纯表情的回复。
- 提问之前请再仔细看一遍楼主的说明,或许是您遗漏了。
- 请勿到处挖坑绊人、招贴广告。既占空间让人厌烦,又没人会搭理,于人于己都无利。
关于好例子网
本站旨在为广大IT学习爱好者提供一个非营利性互相学习交流分享平台。本站所有资源都可以被免费获取学习研究。本站资源来自网友分享,对搜索内容的合法性不具有预见性、识别性、控制性,仅供学习研究,请务必在下载后24小时内给予删除,不得用于其他任何用途,否则后果自负。基于互联网的特殊性,平台无法对用户传输的作品、信息、内容的权属或合法性、安全性、合规性、真实性、科学性、完整权、有效性等进行实质审查;无论平台是否已进行审查,用户均应自行承担因其传输的作品、信息、内容而可能或已经产生的侵权或权属纠纷等法律责任。本站所有资源不代表本站的观点或立场,基于网友分享,根据中国法律《信息网络传播权保护条例》第二十二与二十三条之规定,若资源存在侵权或相关问题请联系本站客服人员,点此联系我们。关于更多版权及免责申明参见 版权及免责申明
网友评论
我要评论