IEC62196-2-2016

【实例简介】
欧标电动汽车充电产品标准，电动汽车传导充电用插头、插座、车辆连接器和车辆插孔第2部分
IECI lEc62196-2 Edition2.02016-02 NTERNATIONAL STANDARD NORME INTERNATIONALE Plugs, socket-outlets, vehicle connectors and vehicle inlets-Conductive charging of electric vehicles Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories Fiches, socles de prise de courant, prises mobiles de vehicule et socles de connecteurs de vehicule- Charge conductive des vehicules electriques Partie 2: Exigences dimensionnelles de compatibilite et d'interchangeabilite pour les appareils a broches et alveoles pour courant alternatif INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE Cs29.120.30:43.120 SBN978-2-8322-3154-8 Warning! Make sure that you obtained this publication from an authorized distributor Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agree O Registered trademark of the Intemational Electrotechnical Commission arque depose de la Commission Electrotechnique Internationale 2 EC62196-2:2016@|EC2016 CONTENTS FOREWORD.… INTRODUCTION Scope.…… 2 Normative references 3 Terms and definitions 4 General 46778888 5 Ratings………,…,………… 6 Connection between the power supply and the electric vehicle 7 Classification of accessories 10 8 Marking… .11 9 Dimensions 11 10 Protection against electric shock 12 11 Size and colour of protective earthing conductors 12 12 Provision for earthing ..12 13 Terminals∴ 12 14 Interlocks 12 15 Resistance to ageing of rubber and thermoplastic material 12 16 General construction ∴12 17 Construction of socket-outlets 12 18 Construction of plugs and vehicle connectors 12 19 Construction of vehicle inlets 12 20 Degrees of protection 13 21 nsulation resistance and dielectric strength………… 13 22 Breaking capacity 13 23 Normal operation 13 24 Temperature rise 13 25 Flexible cables and their connection .13 26 Mechanical strength ∴13 27 Screws, current-carrying parts and connections............ 13 28 Creepage distances, clearances and distances.........................13 29 Resistance to heat to fire and to tracking 13 30 Corrosion and resistance to rusting ..............................................................................13 31 Conditional short-circuit current withstand test 32 Electromagnetic compatibility(EMC)…… .14 33∨ehic| e driveover 201 Components 202 Resistor coding .. 15 STANDARD SHEETS 16 CONFIGURATION TYPE 1 6 CONFIGURATION TYPE 2 28 CONFIGURATION TYPE 3 43 EC62196-2:2016@|EC2016 Table 201-Overview of the basic vehicle interface, configuration type 1, single phase...9 Table 202-Overview of the basic vehicle interface, configuration types 2 and 3 three-phase or single phase.....,.……...10 Tabe203- Configuration types and standard sheets…..…,…,…,…,…,…11 Tabe204- nteroperation of configuration type2 accessories……,……,…….28 Ec62196-2:2016@|EC2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION PLUGS, SOCKET-OUTLETS VEHICLE CONNECTORS AND VEHICLE INLETS- CONDUCTIVE CHARGING OF ELECTRIC VEHICLES Part 2: dimensional com patibility and interchangeability requirements for a.c. pin and contact-tube accessories FOREWORD 1)The International Electrotechnical Commission(IEC)is a worldwide organization for standardization comprising all national electrotechnical committees (EC National Committees). The object of lEc is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications Technical Reports, Publicly Available Specifications (PAs) and Guides (hereafter referred to as"IEC Publication(s)"). Their preparation is entrusted to technical committees: any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the lEc also participate in this preparation. IEc collaborates closely ith the International Organization for Standardization (Iso)in accordance with conditions determined by agreement between the two organizations 2)The formal decisions or agreements of lEc on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National committees 3)IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense, While all reasonable efforts are made to ensure that the technical content of lec Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user 4)In order to promote international uniformity, IEC National Committees undertake to apply lEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter 5)IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to lec marks of conformity iEc is not responsible for any services carried out by independent certification bodies 6) All users should ensure that they have the latest edition of this publication 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and lEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees)and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication 9)Attention is drawn to the possibility that some of the elements of this lEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent right International Standard lEC 62196-2 has been prepared by IEC subcommittee 23H: Plugs socket-outlets and couplers for industrial and similar applications, and for electric vehicles, of lEC technical committee 23: Electrical accessories This second edition cancels and replaces the first edition published in 2011 and constitutes a technical revision This second edition includes the following significant technical changes with respect to the previous edition a) Standard sheets for configurations type 2 and type 3 have been updated )Configuration type 2 is now available with optional shutter. EC62196-2:2016@|EC2016 -5 The text of this standard is based on the following documents CDV Report on voting 23H/324/CDV 23H/342/RvC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table This publication has been drafted in accordance with the Iso/EC Directives, Part 2 A list of all the parts in the IEC 62196 series, under the general title Plugs, socket-outlets, vehicle connectors and vehicle inlets-Conductive charging of electric vehicles, can be found on the iEc website This part of lEc 62196 is to be read in conjunction with IEC 62196-1: 2014. The clauses of the particular requirements in Part 2 supplement or modify the corresponding clauses in Part 1 Where the text indicates addition"to or " replacement"of the relevant requirement, test specification or explanation of Part 1, these changes are made to the relevant text of Part 1 which then becomes part of this standard. Where no change is necessary, the words Clause X of IEC 62196-1: 2014 is applicable"are used. In this standard, the following print types are used requirements proper: in roman type; test specifications: in italic type; notes: in smaller roman type The committee has decided that the contents of this publication will remain unchanged until thestabilitydateindicatedonthelecwebsiteunderhttp://webstore.iecchinthedata related to the specific publication. At this date, the publication will be reconfirmed · withdrawn, replaced by a revised edition, or amended EC62196-2:2016@|EC2016 INTRODUCTION Responding to global challenges of co, reduction and energy security, the automobile industries have been accelerating the development and commercialization of electric vehicles and hybrid electric vehicles. In addition to the prevailing hybrid electric vehicles, battery electric vehicles including plug-in hybrid electric vehicles are going to be mass-marketed. To support the diffusion of such vehicles, this standard provides the standard interface configurations of a c. vehicle couplers and accessories to be used in conductive charging of electric vehicles, taking the most frequent charging situations into consideration lEC 62196 is divided into several parts Part 1: General requirements Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories Part 3: Dimensional compati bility and interchangeability requirements for d. c and a.c. /d.c pin and contact-tube vehicle couplers Ec62196-2:2016@|EC2016 PLUGS, SOCKET-OUTLETS, VEHICLE CONNECTORS AND VEHICLE INLETS-CONDUCTIVE CHARGING OF ELECTRIC VEHICLES Part 2: Dimensional compatibility and interchangeability requirements for a.C. pin and contact-tube accessories Scope This part of lEC 62196 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 480 V a.c., 50 Hz to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This part of IEC 62196 covers the basic interface accessories for vehicle supply as specified in IEC 62196-1, and intended for use in conductive charging systems for circuits specified in EC61851-1:2010. NOTE 1 Electric road vehicles(EV) implies all road vehicles, including plug-in hybrid road vehicles(PHEV), that derive all or part of their energy from REss These accessories are intended to be used for circuits specified in IEc 61851-1: 2010 which operate at different voltages and frequencies and which may include extra-low voltage (ELV) and communication signals These accessories may be used for bidirectional power transfer(under consideration) This standard applies to accessories to be used in an ambient temperature between -30C and+50°C NoTE 2 In the following country, other requirements regarding the lower temperature may apply: No NoTE 3 In the following country, -35C applies: SE These accessories are intended to be connected only to cables with copper or copper-alloy conductors ehicle inlet and vehicle connector to this standard are intended to be used for charging in modes 1, 2 and 3, cases B and C. The socket-outlets and plugs covered by this standard are intended to be used for charging mode 3 only, case A and B The modes and permissible connections are specified in IEC 62196-1: 2014 2 Normative references Clause 2 of IEC 62196-1: 2014 applies except as follows Addition lEC 62196-1: 2014, Plugs, socket-outlets, vehicle connectors and vehicle in/ets- Conductive charging of electric vehicles- Part 1: General requirements Ec62196-2:2016@|EC2016 3 Terms and definitions Clause 3 of lEC 62196-1: 2014 applies 4 General Clause 4 of IEC 62196-1: 2014 applies 5 Ratings Clause 5 of lEC 62196-1: 2014 applies except as follows 5.1 Replacement Rated operating voltages 30V(signal or control purposes only): 250V ac 480Va.c. 5.2 Replacement The rated currents a 2 A(signal or control purposes only) 13 A single phase 16 A single and three-phase 20 A single and three-phase 30 A or 32 A single and three-phase 60 A or 63 A single and three-phase 70 A single phase only NOTE 1 In the following countries, the branch circuit overcurrent protection device is based upon 125 of the accessory rating: US NOTE 2 Reference to"30 A or 32 A"and60 A or 63 A"rating is made in accordance with National requirements 6 Connection between the power supply and the electric vehicle Clause 6 of lEC 62196-1: 2014 applies except as follows 6.1 Replacement This Clause provides a description of the physical conductive electrical interface requirements between the vehicle and the power supply, which allows the following design at the vehicle interface: a basic interface that provides for current ratings up to 63 A a.c. three-phase and up to 70 A a.c. single phase Different configuration types for the basic interface may allow different application of mode and current ratings. See introduction to relevant standard sheets for more details 【实例截图】
【核心代码】