实例介绍
【实例简介】
摄像头自动变焦音圈马达驱动芯片FP5510A 手册，常用于智能手机中
VDD SCL 10-bit dac SDA○ C ○lsNK PS○ POR Vref Power on reset GND e Junction Temperature Stresses beyond those listed under"Absolute Maximum Ratings"may cause permanent damage to the device ● Supply voltage,vDD e Operation Temperature range UA UA/LSB UA UA us IS us SDA tsr U: DAT D: STA SCL tHD: STA HD DAT U STA Ack from FP5510A Ack from FP5510A Ack from FP5510A SDA Al A0RAWYACK PD Busy 00011000 Start Slave Address0x 18 Data1 Data2 top Ack from FP5510A Ack irom master No Acl SCL 8((叫国回国叫k 03D2{D1(00 00011 Start Slave Address=0x 19 Data 1 Data 2 Stop must keep"L at writing operation Power On Wait=12ms Command type One step Mode Linear Slope Control Two Step/ Enhance Slope control Control mode Protection OFF Protection oFF Protection OFF Setting Command TSC/ESC/MC Setting TSC/ESC/MC Setting TSC/ESC/MC Setting (TSC/ESC disable) TSC/eSC disable Protection On ST Setting ST Setting Data[9: 0] Setting Protection on Protection ON Command VCM Drive ne step mode after power on, you don't need register set. Because, tSc/esc disable is default ※ ne step mode after power on, you dont need register set. Because, tSC/ESC disable is default ※ 4: 0] default value is 5b=00000 Sink ML[10]&sT4:0] MS[1:0]=0 MS[1:0}=0 One Step One Step Mode Mode Code per 1step is set Code per 1 step is set by ms[1: 0] by Ms[1: 0 1 step period is set by ML[1:0]&ST4:0] Busy=H Busy=H 【实例截图】
【核心代码】
摄像头自动变焦音圈马达驱动芯片FP5510A 手册，常用于智能手机中
VDD SCL 10-bit dac SDA○ C ○lsNK PS○ POR Vref Power on reset GND e Junction Temperature Stresses beyond those listed under"Absolute Maximum Ratings"may cause permanent damage to the device ● Supply voltage,vDD e Operation Temperature range UA UA/LSB UA UA us IS us SDA tsr U: DAT D: STA SCL tHD: STA HD DAT U STA Ack from FP5510A Ack from FP5510A Ack from FP5510A SDA Al A0RAWYACK PD Busy 00011000 Start Slave Address0x 18 Data1 Data2 top Ack from FP5510A Ack irom master No Acl SCL 8((叫国回国叫k 03D2{D1(00 00011 Start Slave Address=0x 19 Data 1 Data 2 Stop must keep"L at writing operation Power On Wait=12ms Command type One step Mode Linear Slope Control Two Step/ Enhance Slope control Control mode Protection OFF Protection oFF Protection OFF Setting Command TSC/ESC/MC Setting TSC/ESC/MC Setting TSC/ESC/MC Setting (TSC/ESC disable) TSC/eSC disable Protection On ST Setting ST Setting Data[9: 0] Setting Protection on Protection ON Command VCM Drive ne step mode after power on, you don't need register set. Because, tSc/esc disable is default ※ ne step mode after power on, you dont need register set. Because, tSC/ESC disable is default ※ 4: 0] default value is 5b=00000 Sink ML[10]&sT4:0] MS[1:0]=0 MS[1:0}=0 One Step One Step Mode Mode Code per 1step is set Code per 1 step is set by ms[1: 0] by Ms[1: 0 1 step period is set by ML[1:0]&ST4:0] Busy=H Busy=H 【实例截图】
【核心代码】
标签：
好例子网口号：伸出你的我的手 — 分享！
网友评论
小贴士
感谢您为本站写下的评论，您的评论对其它用户来说具有重要的参考价值，所以请认真填写。
- 类似“顶”、“沙发”之类没有营养的文字，对勤劳贡献的楼主来说是令人沮丧的反馈信息。
- 相信您也不想看到一排文字/表情墙，所以请不要反馈意义不大的重复字符，也请尽量不要纯表情的回复。
- 提问之前请再仔细看一遍楼主的说明，或许是您遗漏了。
- 请勿到处挖坑绊人、招贴广告。既占空间让人厌烦，又没人会搭理，于人于己都无利。
关于好例子网
本站旨在为广大IT学习爱好者提供一个非营利性互相学习交流分享平台。本站所有资源都可以被免费获取学习研究。本站资源来自网友分享，对搜索内容的合法性不具有预见性、识别性、控制性，仅供学习研究，请务必在下载后24小时内给予删除，不得用于其他任何用途，否则后果自负。基于互联网的特殊性，平台无法对用户传输的作品、信息、内容的权属或合法性、安全性、合规性、真实性、科学性、完整权、有效性等进行实质审查；无论平台是否已进行审查，用户均应自行承担因其传输的作品、信息、内容而可能或已经产生的侵权或权属纠纷等法律责任。本站所有资源不代表本站的观点或立场，基于网友分享，根据中国法律《信息网络传播权保护条例》第二十二与二十三条之规定，若资源存在侵权或相关问题请联系本站客服人员，点此联系我们。关于更多版权及免责申明参见 版权及免责申明
支持(0) 盖楼(回复)