火牛跑马灯实验（火牛开发板-UGPIO）

【实例截图】

【核心代码】

/**************************************************************
** 	火牛开发板
**	UGPIO测试
**  版本：V1.0  
**	论坛：www.poweravr.com
**	淘宝：www.openmcu.com   
**  技术支持群：121939788 
***************************************************************/
#include "stm32f10x.h"
#include "GLCD.h"
#include "USART.h"

void GPIO_Configuration(void)
{
	GPIO_InitTypeDef GPIO_InitStructure;
	
	/* Configure IO connected to LD1, LD2, LD3 and LD4 leds *********************/	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 | GPIO_Pin_11;
  	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
  	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  	GPIO_Init(GPIOD, &GPIO_InitStructure);


	/*  Configure IO connected to BeeP  */
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
  	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
  	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  	GPIO_Init(GPIOB, &GPIO_InitStructure);

   	/* Configure USART1 Tx (PA.09) as alternate function push-pull */
  	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
  	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  	GPIO_Init(GPIOA, &GPIO_InitStructure);
    
  	/* Configure USART1 Rx (PA.10) as input floating */
  	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
  	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  	GPIO_Init(GPIOA, &GPIO_InitStructure);
}

//系统中断管理
void NVIC_Configuration(void)
{ 
  	/* Configure the NVIC Preemption Priority Bits */  
  	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0);

	#ifdef  VECT_TAB_RAM  
	  /* Set the Vector Table base location at 0x20000000 */ 
	  NVIC_SetVectorTable(NVIC_VectTab_RAM, 0x0); 
	#else  /* VECT_TAB_FLASH  */
	  /* Set the Vector Table base location at 0x08000000 */ 
	  NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);   
	#endif
}

//配置系统时钟,使能各外设时钟
void RCC_Configuration(void)
{
	SystemInit();	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA 
                           |RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC
                           |RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOE
						   |RCC_APB2Periph_ADC1  | RCC_APB2Periph_AFIO 
                           |RCC_APB2Periph_SPI1, ENABLE );
  // RCC_APB2PeriphClockCmd(RCC_APB2Periph_ALL ,ENABLE );
     RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4 
                           |RCC_APB1Periph_USART3|RCC_APB1Periph_TIM2	                           
                           , ENABLE );
	 RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
}

void InitDis(void) 
{
   /* LCD Module init */
   GLCD_init();
   GLCD_clear(White);
   GLCD_setTextColor(Blue);
   GLCD_displayStringLn(Line1, "     FireBull");
   GLCD_displayStringLn(Line2, "   GPIO example");
   GLCD_setTextColor(Red);
}

//配置所有外设
void Init_All_Periph(void)
{
	RCC_Configuration();	
	InitDis();
	GPIO_Configuration();
	NVIC_Configuration();
	USART1_Configuration();
	USART1Write((u8*)"    FireBull  GPIO_example",sizeof("    FireBull  GPIO_example"));
}

void Delay(vu32 nCount)
{
  for(; nCount != 0; nCount--);
}

int main(void)
{  
	Init_All_Periph();
 	while(1)
  	{
    	/* Turn on LD2 and LD3 */
    	GPIO_SetBits(GPIOD, GPIO_Pin_8);
    	/* Turn off LD1 */
    	GPIO_ResetBits(GPIOD, GPIO_Pin_9 | GPIO_Pin_10 | GPIO_Pin_11);
    	/* Insert delay */
    	Delay(0xEFFFF);

    	/* Turn on LD2 and LD3 */
    	GPIO_SetBits(GPIOD, GPIO_Pin_9);
    	/* Turn off LD1 */
    	GPIO_ResetBits(GPIOD, GPIO_Pin_8 | GPIO_Pin_10 | GPIO_Pin_11);
    	/* Insert delay */
    	Delay(0xEFFFF);

    	/* Turn on LD4 */
    	GPIO_SetBits(GPIOD, GPIO_Pin_10);
    	/* Turn off LD2 and LD3 */
    	GPIO_ResetBits(GPIOD, GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_11);
    	/* Insert delay */
    	Delay(0xEFFFF);

    	/* Turn on LD4 */
    	GPIO_SetBits(GPIOD, GPIO_Pin_11);
    	/* Turn off LD2 and LD3 */
    	GPIO_ResetBits(GPIOD, GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10);
    	/* Insert delay */
    	Delay(0xEFFFF);
    	GPIO_ResetBits(GPIOD, GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10);

  	}
}