NI-DAQmx and DAQ Device 安装指导

【实例简介】
Install NI application software, such as NI LabVIEW, or another application development environment (ADE), such as ANSI C or Visual Basic .NET. Refer to the NI-DAQmx Readme on the software media for supported application software and ADE versions.
CompactDAQ Devices Complete the following steps to install aC Series 1O module in a CompactDAQ system 1. Attach a ring lug to a 14 AwG(.6 mm)wire Connect the ring lug to the ground terminal on the side of the NI cdaQ chassis using the ground screw Attach the other end of the wire to the systen safety ground Additionally, attach a wire with a ring lug to all other C Series lo module cable shields. You must connect this wire to the ground terminal of the chassis using the ground screw △ Caution If hazardous voltages. greater than 42 4v or 60 vdc to earth ground, are present, special safety guidelines apply. refer to the C Scrics module uscr guidc bcforc continuing 2. Install C Series 1O modules. Squeeze both C Series 1O module latches insert each I/O module into an empty module slot, and press until both atches lock the module in place. Refer to the c series i/o module user guide for more information, such as signal connections, safety precautions, and module ratings 1 USB or Ethernet Connector 2 C Series I/O Module Figure 1. Setting up a cDAQ Chassis 3. If you have a USB cDAQ chassis, connect the chassis using the USB cable supplied with your chassis to any available USB port on your computer system. If you have an Ethernet cDAQ chassis, connect the chassis to your network using a Cat5e or crossover Ethernet cable. Refer to the daQ getting Started Guide for network configuration information 4. Connect the power source to the chassis. Most cDaQ chassis require an external power supply that meets the specifications listed in the chassis user documentation C National Instruments Corporation N/-DAOmx and daQ Device /nstallation Guide PCI and PCI Express Devices Complete the following steps to install a PCI and PCI Express device 1. Power off and unplug the computer 2. Rcmovc thc computcr cover and/or thc expansion slot cover 3. Touch any metal part of the computer to discharge any static electricity 1 PCI/PCI Express DAQ Device 3 PC with PCI/PCI Express Slot 2 PCI/PCI Express System Slot Figure 2. Installing a PCl/PCl Express Device 4. Insert the device into the applicable PCl/PCI Express system slot. Gently rock the device into place. Do not force the device into place Per the pci standard ni pci dao devices with the universal PCI connector are supported in PCI-compliant buses, including PCI-X You cannot install PCI Express devices in PCi slots and vice versa PCI Express devices support up-plugging into a PCI Express slot of higher lane width. For guidelines, refer to ni. com/pciexpress 5. Secure the device mounting bracket to the computer back panel rail 6.(Optional)On NI M and X Series PCI Express devices, such as the NI PCIe-625x/635x, connect the PC and the device disk drive power connectors. Refer to the device user manual on the Ni-daQmx media for hen to use the disk drive power connector. Use a disk drive power connector that is not in the same power chain as the hard drive 1 Device disk drive power connector 2 PC Disk Drive Power Connector Figure 3. Attaching Disk Drive Power to the PCI Express Device N/-DAgmx and dAQ Device installation guid n. com Connecting or disconnecting the disk drive power connector can affect the analog performance of your device. To compensate for this NI recommends that you self-calibrate the PCI Express daQ device in MAX after connecting or disconnecting the disk drive power connector refer to the DAQ Getting Started Guide at Start> All Programs> National Instruments>NI-DAQ DAQ Getting Started Guide. 7. Replace the computer cover, if applicable 8. Plug in and powcr on your computcr PXI and pXI Express Devices Complete the following steps to install a PXI and PXI Express device 1. Power off and unplug the pxi/PXI Express chassis. Refer to your chassis manual to install or configure the chassis Caution Refer to the Read Me ]irst: Safety and Electromagnetic Compatibility with your PXIPXI Exprcss chassis or dcvicc bcforc removing covers or connecting or disconnecting signal wires 1 PXI/PXI Express Chassis 5 Front-Panel Mounting Screws 2 PXI/PXI Express System Controller 6 Module guides 3PXP× Express Module 7 Power Switch 4 Injector/Ejector Handle Figure 4. Installing a PXI/PXI Express device in the chassis 2. Identify a supported PXIPXI Express slot in the chassis. Some devices have PXI/PXI Express slot requirements; for information, refer to the device documentation C National Instruments Corporation N/-DAOmx and daQ Device /nstallation Guide 2 (4 1 PXI Express System Controller Slot 3 PXI Express Hybrid Peripheral slot 2 PXI Express Peripheral Slot 4 PXI Express System Timing Slot Figure 5. Symbols for PXI Express/PXI Express Hybrid/PXI Slots If you are using a PXI Express chassis, you can place Pxi devices in the PXI Slots. If a PXI device is hybrid slot compatible, you can use the PXI Express Hybrid slots. PXI Express devices can be placed only in PXI Express slots and PXI Express llybrid slots. Refer to the chassis documentation for details 3. Remove the filler panel of an unused pXI/PXI Express slot 4. Touch any metal part of the chassis to discharge static electricity 5. Ensure that the PXI/PXI Express module injector/ejector handle is not latched and swings freel 6. Place the PXIPXI Express module edges into the module guides at the top and bottom of thc chassis 7. Slide the device into the pxiPXi Express slot to the rear of the chassis 8. When you begin to feel resistance, pull up on the injector/ejector handle to latch the device 9. Secure the device front panel to the chassis using the front-panel 10. Plug in and power on your PXI/PXI Express chassis USB Devices computer. Complete these steps to install an ni device for USB. On your You must be an administrator to install ni software and devices 1. Make power connections If you are using the BP-1 battery pack, install it as described in your BP-l installation guide an external power supply, verify that the voltage on the externa/ Somc nI devices for USB rcquirc cxtcrnal powcr. If your devicc ha power supply, if any, matches the voltage in your area(for example, 120 or 230 VAC)and the voltage required by your device 2. Connect the power supply or power cord to an electrical outlet and your 3. Connect the cable from the computer USB port or from any other hub to any available usb port on the device N/-DAgmx and dAQ Device installation guid n. com 4. If you have a usB device with a power switch, power on the device The computer should immediately detect your device When the computer recognizes a uSB device, the led on the device blinks or lights up Refer to the device documentation for LEd pattern descriptions Windows Device recognition Windows versions earlier than Windows vista recognize newly installed devices when the computer restarts. Vista installs device software automatically If the Found New Hardware wizard opens, Install the software automatically as recommended for each device NI Device monitor After Windows detects newly installed NI USB devices, NI Device Monitor runs automatically at startup Make sure the ni device Monitor icon, shown at left, is visible in the taskbar notification area, Other wise. the ni device monitor does not open. To turn the NI Device Monitor on, unplug your device, restart NI Devicc Monitor by sclccting Start>All Programs>Nationa InstrumentS>NI-DAQNI Device Monitor, and plug in your evice The NI Device Monitor prompts you to select from the following options These options may vary, depending on the devices and software installed on our system Begin a measurement with This Device Using NI lab VIEW SignalExpress--Opcns an NI-DAQmx stcp that uscs thc channcls from your device in Lab VIEW SignalExpress Begin an application with This Device--Launches Lab VIEw. Choose this option if you have already configured your device in MAX Run Test Panels--Launches MAX test panels for your device Configure and Test This Device--Opens MAX Take No Action--Recognizcs your device but docs not launch an application Thc following fcaturcs arc availablc by right-clicking the N Dcvicc Monitor Icon Run at Startup-Runs NI Device Monitor at system startup(default) Clear all Device Associations-Select to clear all actions set by the Always Take This action checkbox in the device auto-launch dialog Close--Turns off ni device monitor. To turn on ni device monitor select Start> All Programs> National Instruments>N-DAQy NI Device monitor C National Instruments Corporation N/-DAOmx and daQ Device /nstallation Guide Accessories Install accessories and/or terminal blocks according to the instructions in their installation guides. For SCXI and SCC signal conditioning systems, continue with the instructions in the DAQ Getting Started guide. Troubleshooting If you have problems installing your software, go to ni. com/ support/ daqmx For hardware troubleshooting. go to ni. com/support and enter your device name, or go to ni. com/kb If you need to return your National Instruments hardware for repair or device calibration, go to ni. com/info and enter rasen to start the return Merchandise Authorization(rMa)process Go to ni con/ info and enter rddq8x for a complete listing of the NI-DAQmx documents and their locations Next ste To confirm your device is working properly and start your application, refer to the dag Getting Started Guide. After you install NI-DAQmx, the NI-DAQmx software documents are accessible from Start All Programs> National Instruments>NI-DAQ NI-DAQmx document title. Additional resources are online at ni. com/gettingstarted The following table lists device terminal pinout locations Location How to access pinout MAX Righil-click the device naine under Devices and Interfaces and select device pinouts Right-click the device name under Devices and Interfaces, and select Help> online Device Documentation. A browser window opens to r i. com/manuals with the results of a scarch for rclcvant dcvicc documents DAQ ASSistant Select the task or virtual channel. and click the Connection Diagram tah. Select each virtual channel the task NI-DAQIIX Help Select Start>All Programs>National Instrunents>> NI-DAQ>NI-DAQmx Help ni. com/manuals Refer to the device documentation I atVIFW, National Instruments, NI, ni. com, the National Instru ments corporate logo, and the Fagle logo are trademarks nf National Instruments Corporation. Refer: o he Trademark Information at ni. com/trademarks for other National Ins: ruments trademarks. Othier pruduct and ccinlpally lainles mentioned herein are tra ks ur trade amies of tie r respective CUnlpaies For patents covering Natianal InstrumEnts products/technclogy, reter to the appropriate location: Help >Patents in your software patents. txt file on your media or the National instrumens Parent Notice at ni. com/patents 010 National Instruments Corp. All rights reserved 33235U Julio INITIATION A DAO A lire en premier Guide d'installation de NI-DAQmx et des peripheriques DAQ Installer les logiciels avant d installer de nouveaux materiels Installez les logiciels d'application Installez les logiciels application NI, comme NI Lab VIEW, ou un autre cnvironncmcnt dc devcloppcmcnt d application(ADE), comme ANSI C ou Visual Basic. NET. Reportez-vous au fichier Readme Nl-DAOmx sur le media de logiciels pour savoir quels logiciels d application et versionS ADE sont supportes Faites une copie de sauvegarde de toutes vos applications avant de mettre le logiciel a jour ou de modifier I application Installez NI-DAQmx Installez le driver NI-DAQmx avant d installer de nouveaux peripheriques materiels, de sorte que Windows puisse les detecter 1. Inserez le media du logiciel Si linstalleur NI-DaQmx ne souvre pas automatiquement, selectionnez Demarrer> Executer Entrez x: \autorun. exe, x ctant la lettre du lcctcur Suivez lcs instructions qui s affichent 2. Enregistrez votre materiel Ni en ligne, surni. com/register lorsque le stem vous y invite 3. La derniere boite de dialogue vous propose les options suivantes Cliquez sur Redemarrer ulterieurement pour installer un autre logiciel Ni ou de la documentation supplementaire. Si vous utilisez un lien MxI-3 a partir d'un PC pour controler un chassis PXl, yous devez quitter le programme et installer le logiciel MXI-3, disponible sur ni. com/downloads, avant d'utiliscr Ic pcriphcriquc DAQ Cliquez sur Arreter ou Redemarrer si vous etes pret a installer ore periphcriquc Cliquez sur Redemarrer si vous utilisez un systeme qui execute le module lab vieW rcal-Timc. Tclechargcz NI-DaQ sur la cible cn utilisant MAX. Reportez-vous a l' Aide MAX sur les systemes deportes en selectionnant Aide> Rubriques de laide>systemes deportes dans max Si vous avez des difficultes a installer votre logiciel, allez sur ni. com/ support/daqmx NATIONAL NSTRUMENTS Deballez les peripheriques, les accessoires et les cables, et installez-es Sortez le peripherique de son emballage et inspectez-le. Contactez Ni si le peripherique est endommage N'installez pas un peripherique endommage Si vous devez installer plusieurs peripheriques DAQ, installez-les tous maintenant en utilisant la procedure appropriee a chaque peripherique si votre systeme comporte des modules scxI a connecter a des peripheriques DAQ, installez dabord les composants DAQ △ Attention Ce peripherique est sensible a l'electricite statique Mettez toujours I'equipement a la masse lorsque vous manipulez votrc periphcriquc ou quc Yous lc conncctcz, ct assurcz-vous d'Ctrc vous-mcmc relic a la masse Pour consulter les informations relatives a la securite et la conformite reportez-vousaladocumentationduperipherique,disponiblesurni.com/ manuals ou sur le media de logiciels NI-DAQmx L es symboles suivant s peuvent figurer sur votre peripherique Ccttc iconc signal un avcrtisscment qui vous indiquc lcs precautions a prendre pour eviter des prejudices corporals, des pertes de donnees ou un crash du systeme Lorsque ce symbole est present sur le peripherique, reportez-vous au document Read Me First: Safety and Electromagnetic Compatibility pour savoir quelles precautions vous devez prendre La presence de ce symbole sur un produit indique une mise en garde vous conseillant de prendre des precautions pour eviter les chocs clcctriqucs △ La presence de ce symbole sur un produit indique qu'un composant risque d etre brulant. Toucher ce composant peut entrainer des blessures Peripheriques CompactDAQ Effectuez les etapes suivantes pour installer un module d'e/s de la serie C dans un systeme CompactDAQ 1. Attachez une bague de retenue a un cable 14 AWG(1, 6 mm). A laide de la vis de masse. connectez la bague de retenue au terminal de masse sur le cote du chassis cDAQ NI. Attachez Iautre extremite du fil a la masse du systeme De plus, attachez un fil avec une bague de retenue a tous les auti blindagcs dcs cables du moduled'e/S dc la seric C. Vous dcvcz conncctcr ce fil au terminal de masse du chassis en utilisant la vis de masse 【实例截图】
【核心代码】