实例介绍
【实例简介】
getting started with Q3D Extractor~ ansys Q3D 软件简明教程，有图形说明，和具体介绍~
Conventions Used in this Guide Alternate methods or tips are / isted in the left margin in blue italic lext Getting Help ANSYS Technical Support 1. Introduction The via model ...,,.,,1-2 2. Creating the Via Model Open Q3d Extractor and save a new project. 2-2 Set the Drawing Units 2-2 Create the vias central barrel 2-3 Create the first via pad .2-3 Duplicate the First Via Pad 2-4 Create Geometric variables .2-5 Assign a variable to the Center Barrel 2-6 Assign a variable to the Pads 2-6 Draw the trace Stubs ....,2-7 Unite via objects ....2-8 Create the ground plane 2-9 Create the Antipad 2-10 Define the background material ....2-12 3. Setting Up the Simulation Set Up Sources and sinks.........3-2 Define the source 3-2 Assign the sink Identify the Nets ..,,,3-5 Add a Solution Setup 3-6 Validate the Setup 3-6 Solve the probl 3-7 Generate a field plot 3-8 Export a Circuit Model 3-9 4. Setting Up a Parametric Analysis Add a Parametric Sweep 4-2 Run the Parametric Analysis........4-3 5. Comparing the Solutions lot the result 5-2 Plot the Results After Changing Capacitance.. 5-4 Modity the Pad Radius Run Parametric Analysis 1 5-4 Plot results....,,,,,,,,,,,,,,, Close the project and exit Q3d Extractor 5-7 Estimated time to complete this guide 60 minutes The via model Estimated time to complete this chapter. 20 minutes 【实例截图】
【核心代码】
getting started with Q3D Extractor~ ansys Q3D 软件简明教程，有图形说明，和具体介绍~
Conventions Used in this Guide Alternate methods or tips are / isted in the left margin in blue italic lext Getting Help ANSYS Technical Support 1. Introduction The via model ...,,.,,1-2 2. Creating the Via Model Open Q3d Extractor and save a new project. 2-2 Set the Drawing Units 2-2 Create the vias central barrel 2-3 Create the first via pad .2-3 Duplicate the First Via Pad 2-4 Create Geometric variables .2-5 Assign a variable to the Center Barrel 2-6 Assign a variable to the Pads 2-6 Draw the trace Stubs ....,2-7 Unite via objects ....2-8 Create the ground plane 2-9 Create the Antipad 2-10 Define the background material ....2-12 3. Setting Up the Simulation Set Up Sources and sinks.........3-2 Define the source 3-2 Assign the sink Identify the Nets ..,,,3-5 Add a Solution Setup 3-6 Validate the Setup 3-6 Solve the probl 3-7 Generate a field plot 3-8 Export a Circuit Model 3-9 4. Setting Up a Parametric Analysis Add a Parametric Sweep 4-2 Run the Parametric Analysis........4-3 5. Comparing the Solutions lot the result 5-2 Plot the Results After Changing Capacitance.. 5-4 Modity the Pad Radius Run Parametric Analysis 1 5-4 Plot results....,,,,,,,,,,,,,,, Close the project and exit Q3d Extractor 5-7 Estimated time to complete this guide 60 minutes The via model Estimated time to complete this chapter. 20 minutes 【实例截图】
【核心代码】
标签：
好例子网口号：伸出你的我的手 — 分享！
相关软件
小贴士
感谢您为本站写下的评论，您的评论对其它用户来说具有重要的参考价值，所以请认真填写。
- 类似“顶”、“沙发”之类没有营养的文字，对勤劳贡献的楼主来说是令人沮丧的反馈信息。
- 相信您也不想看到一排文字/表情墙，所以请不要反馈意义不大的重复字符，也请尽量不要纯表情的回复。
- 提问之前请再仔细看一遍楼主的说明，或许是您遗漏了。
- 请勿到处挖坑绊人、招贴广告。既占空间让人厌烦，又没人会搭理，于人于己都无利。
关于好例子网
本站旨在为广大IT学习爱好者提供一个非营利性互相学习交流分享平台。本站所有资源都可以被免费获取学习研究。本站资源来自网友分享，对搜索内容的合法性不具有预见性、识别性、控制性，仅供学习研究，请务必在下载后24小时内给予删除，不得用于其他任何用途，否则后果自负。基于互联网的特殊性，平台无法对用户传输的作品、信息、内容的权属或合法性、安全性、合规性、真实性、科学性、完整权、有效性等进行实质审查；无论平台是否已进行审查，用户均应自行承担因其传输的作品、信息、内容而可能或已经产生的侵权或权属纠纷等法律责任。本站所有资源不代表本站的观点或立场，基于网友分享，根据中国法律《信息网络传播权保护条例》第二十二与二十三条之规定，若资源存在侵权或相关问题请联系本站客服人员，点此联系我们。关于更多版权及免责申明参见 版权及免责申明
网友评论
我要评论